How to Replace a Tub Yourself: Removing and Replacing.
How to Replace a Tub Yourself: Removing and Replacing.
Blog Article
On this page below you can get additional superb resources relating to How to Install a Bathtub Yourself.
Installing a tub isn't exactly brain surgery, yet it does need solid plumbing, carpentry, and also sometimes, tiling skills. Changing an old bath tub with a brand-new one is also a moderately tough project. If the old tub is readily easily accessible, the project can relocate immediately; if you need to open a wall surface to eliminate the old bathtub as well as place the brand-new bath tub, the job is a lot harder. In either case, the project is within a home handyman's skills, although you will certainly require a helper to move out the old tub and embeded in the new one. Make sure you have actually qualified yourself for the work as well as fit attempting it. As opposed to employing a professional to take control of a halfway-completed project, it is better to think about utilizing one prior to you begin. Opportunities are you might need a professional plumber to make tube connections.
This write-up will assist you set up a brand-new bathtub in your shower room if you have currently purchased a new bathtub and also don't need to transform the arrangement of your previous water pipes.
Your devices and product list should make up the following:
Preparing for the Installation
Firstly, the supporting framework provided with the bath ought to be fitted (if called for) according to the manufacturer's directions. Next, fit the faucets or mixer to the bathtub. When fitting the tap block, it is necessary to ensure that if the tap features a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bath, it is also practical to fit a sustaining plate under the faucets system to stop pressure on the tub.
Fit the flexible faucet ports to the bottom of the two taps using 2 nuts and olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bath. Use the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Make certain you use all of the provided washing machines.
Attach the catch to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bathroom need to currently prepare to be suited its final position.
Removing Old Taps
If you need to replace old taps with new ones as a part of your installment, then the first thing you need to do is disconnect the water system. After doing so, activate the taps to drain pipes any kind of water staying in the system. The procedure of removing the existing faucets can be fairly bothersome as a result of the limited accessibility that is often the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipelines to the faucets. Have a cloth all set for the continuing to be water that will certainly come from the pipelines. As soon as the supply pipes have been gotten rid of, use the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary faucets from turning during this procedure. Once the faucets have actually been eliminated, the holes in the bath/basin will have to be cleansed of any kind of old securing compound.
Before moving on to fit the brand-new faucets, compare the pipeline links on the old taps to the brand-new faucets. If the old taps are longer than the new faucets, then a shank adapter is required for the brand-new taps to fit.
Installing the Bath tub
Using both wooden boards under its feet, place the bath tub in the called for setting. The wooden boards are practical in uniformly spreading out the weight of the tub over the area of the boards as opposed to focusing all the weight onto four tiny points.
The following goal is to ensure that the bath tub is leveled all round. This can be accomplished by examining the spirit level and also changing the feet on the bath tub up until the level checks out degree.
To set up taps, fit the bottom of the outermost flexible tap adapter to the proper supply pipeline by making a compression join; then do the same for the other tap.
Turn on the supply of water and examine all joints and also new pipework for leakages as well as tighten them if essential. Fill up the bathtub and additionally inspect the overflow electrical outlet and the regular outlet for leaks.
Ultimately, deal with the bathroom paneling as explained in the supplier's instruction manual. Tiling as well as securing around the tub needs to wait until the tub has actually been used at the very least once as this will resolve it into its last placement.
Fitting New Touches
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic port to prevent damage to the string. One end of the port fits on the plastic tail of the faucet and the various other end provides a link to the existing supply pipes.
If you require to fit a monobloc, then you will need lowering couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next, position the tap in the placing opening in the bath/basin guaranteeing that the washing machines remain in area between the tap as well as the sink. Safeguard the faucet in place with the producer offered backnut. Once the tap is safely in position, the supply pipelines can be connected to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with typical faucet connectors. The former type must be connected to the faucet finishes first, tightening only by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Bathtub
In the area where the bathroom fulfills the tile, it is necessary to seal the joins with a silicone rubber caulking. This is important as the fitting can move enough to split a stiff seal, creating the water to permeate the wall surface in between the bath and the tiling, leading to complications with dampness and possible leaks to the ceiling listed below.
You can pick from a selection of coloured sealers to blend in your fixtures and installations. They are marketed in tubes and also cartridges, and also can sealing gaps approximately a size of 3mm (1/8 inch). If you have a larger gap to load, you can fill it with twists of drenched newspaper or soft rope. Remember to always fill the bath tub with water before sealing, to permit the motion experienced when the tub remains in usage. The sealant can fracture relatively early if you do not take into account this activity before sealing.
Additionally, ceramic coving or quadrant tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise easily offered on the marketplace. It is a good idea to fit the floor tiles utilizing waterproof or water-proof sticky and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you enjoy more info about How to Install a Bathtub? Write a remark below. We would be glad to see your thoughts about this write-up. We hope to see you back again before long. You should take a moment to distribute this entry if you enjoyed it. We appreciate reading our article about A Step-by-Step Guide to Installing a Bathtub.
Get Quote Report this page